Disclosure: we may earn a commission from links on this page, at no cost to you. How we choose filters.

Short answer
Austin tap water meets or exceeds EPA and Texas (TCEQ) requirements, according to Austin Water’s 2025 Annual Water Quality Report, and the report lists no violations. It is only moderately hard and the city says its public system is free of lead pipes, so for most Austin homes a filter is about removing the chloramine taste rather than solving a compliance problem.
Key takeaways
- Clean compliance record in the 2025 report: no violations listed, no E. coli positive samples, and no Cryptosporidium found in 12 tests.
- Moderate hardness: 93 ppm on average (5.4 grains per gallon), which is softer than much of Texas.
- Lead was very low: the 90th percentile was below 1.0 ppb in 2024 sampling, and no home was over the action level.
- Chloramine is the disinfectant, so pick a filter rated for chloramine if taste or smell is your complaint.
Where Austin tap water comes from
Every glass of Austin tap water starts in the Lower Colorado River as it passes through Lake Travis and Lake Austin, two reservoirs on the Highland Lakes chain west of downtown. Austin Water draws from those lakes and treats the water at three plants: Handcox, Davis and Ullrich.
Because the supply is surface water, treatment focuses on removing particles and microbes. The report shows turbidity, a measure of cloudiness, ranged from 0.02 to 0.11 NTU, far under the treatment standard. Austin uses chloramine to keep water disinfected on its way through the pipes; the 2025 report lists an average residual of 2.3 ppm and a range of 0.06 to 3.1 ppm, under the 4 ppm maximum. Fluoride is added, and it averaged 0.66 ppm.
The plants also track total organic carbon, the natural plant material that reacts with disinfectants to form byproducts. Austin’s removal ratio averaged 1.27 against a required minimum of 1.0, meaning the plants removed more organic material than the rule demands.
Austin water hardness
Austin water hardness ranged from 70 ppm (4.1 grains per gallon) to 126 ppm (7.4 grains per gallon) in 2025, with an average of 93 ppm, or 5.4 grains per gallon, measured as calcium carbonate. There is no legal limit for hardness.
On the usual scale, that average falls in the “moderately hard” band. You will still see some spotting on glassware and a little scale around faucets over time, but it is far milder than in San Antonio, where the utility lists 15 to 20 grains per gallon. For most Austin homes, a full water softener is optional. People with tankless water heaters or espresso machines sometimes add one to protect the equipment, but many households are fine with a vinegar wipe-down now and then. If scale is your main worry, compare options on our whole-house filters page.
Detected contaminants in Austin tap water
These numbers come straight from Austin Water’s 2025 report. Where the report gives an average, it appears in parentheses.
| Contaminant | Highest level | Legal limit (MCL) | Health goal (MCLG) | Typical source |
|---|---|---|---|---|
| Total trihalomethanes (TTHM) | 53.9 ppb (highest LRAA 45.5) | 80 ppb | none | Disinfection byproduct |
| Haloacetic acids (HAA5) | 21.1 ppb (highest LRAA 15.6) | 60 ppb | none | Disinfection byproduct |
| Cyanide | 80 ppb (avg 50) | 200 ppb | 200 ppb | Factory discharge |
| Fluoride | 0.71 ppm (avg 0.66) | 4 ppm | 4 ppm | Water additive; natural erosion |
| Nitrate (as N) | 0.11 ppm (avg 0.05) | 10 ppm | 10 ppm | Fertilizer runoff, septic systems |
| Barium | 0.015 ppm (avg 0.012) | 2 ppm | 2 ppm | Drilling waste, natural erosion |
| Simazine (2024) | 0.08 ppb (avg 0.03) | 4 ppb | 4 ppb | Herbicide runoff |
| Beta/photon emitters (2024) | 4.5 pCi/L | 50 pCi/L | 0 | Natural and man-made deposits |
| Turbidity | 0.11 NTU | Treatment technique | n/a | Soil runoff |
Every result above is well under its limit. The disinfection byproducts (TTHM and HAA5) form when the disinfectant reacts with natural organic matter from the lakes, and Austin’s running averages sit at roughly half of the federal limits.
On PFAS, Austin Water says its monitoring found little to no detectable traces in the city’s drinking water. It points customers to its PFAS webpage and its 2024 report for details, since some PFAS rules are still being phased in.
Lead and copper
Austin Water tests lead and copper at customer taps every three years, and the 2025 report shows the 2024 round:
- Lead: 90th percentile below 1.0 ppb; individual results ranged from 0 to 5.1 ppb. Action level is 15 ppb. No sample exceeded it.
- Copper: 90th percentile below 0.008 ppm. Action level is 1.3 ppm. No sample exceeded it.
In October 2024 the utility confirmed that its public water system is free of lead pipes. A small number of galvanized lines still need replacement, and the city says those owners have been notified and offered free replacement. You can look up your own line in Austin Water’s service line inventory map. Brass fixtures and old solder inside a home can still add a small amount of lead, so running the tap briefly after water has sat overnight is a sensible habit.
Violations
None reported. The 2025 report says Austin Water meets or exceeds EPA and TCEQ requirements, and no Level 1 or Level 2 assessment was triggered.
Do you need a filter in Austin?
For most homes, a filter here is about taste, not safety:
- Chloramine or “pool” taste: a carbon filter certified for chloramine reduction. Under-sink units and whole-house carbon systems both work.
- Renters or tight budgets: a pitcher filter certified for chlorine taste and odor is an easy first step.
- Lowest possible byproducts, PFAS and dissolved solids at the kitchen tap: an under-sink reverse osmosis system.
- Hill Country homes on a private well, outside Austin Water’s service area, are not covered by this report; see our well water guide.
FAQ
Is Austin tap water safe to drink?
Austin Water’s 2025 report says its water meets or exceeds EPA and TCEQ requirements and lists no violations. Lead at the 90th percentile was below 1.0 ppb in 2024, and the utility reports little to no detectable PFAS.
Is Austin water hard or soft?
Moderately hard. The 2025 report shows an average of 93 ppm (5.4 grains per gallon), with a range of 70 to 126 ppm.
Does Austin add fluoride to its water?
Yes. Fluoride is added as a water additive, and the 2025 report shows it ranged from 0.59 to 0.71 ppm with an average of 0.66 ppm, well under the 4 ppm limit.
Sources
Values change every year; the figures here come from Austin Water’s 2025 report.
Sources: Austin Water, 2025 Annual Water Quality Report; Austin Water quality reports page.