Disclosure: we may earn a commission from links on this page, at no cost to you. How we choose filters.

Short answer: Minneapolis tap water met every federal drinking water standard in 2025, according to the city’s 2025 water quality report, and no contaminant was found at a level that broke a federal limit. The water comes from the Mississippi River, is disinfected with chloramine, and is only moderately hard, so most homes need a filter for taste or chloramine rather than for safety.
This page walks through what the City of Minneapolis reported about its drinking water for calendar year 2025: the source, the treatment chemicals you can taste, every detected contaminant with its legal limit, the lead results, and which filter types actually match those findings. All figures come from the utility’s own documents. Values change from year to year, so treat this as a snapshot of the 2025 report rather than a permanent rating.
Key takeaways
- No federal violations: the city says nothing it detected in 2025 exceeded a federal standard.
- Chloramine averaged up to 3.27 ppm, close to the 4.0 ppm ceiling, which is why many residents notice a chemical taste. Catalytic carbon handles chloramine better than a basic pitcher.
- Lead at the tap was low (90th percentile 2 ppb in the 2024 round), but the city is still replacing lead service lines, so older homes should test.
- PFAS levels were very low, with PFBA as the main compound detected (up to 12.00 ppt). PFOA and PFOS do not appear in the report’s detected table.
Where Minneapolis tap water comes from
Every glass of Minneapolis tap water starts in the Mississippi River. Because it is surface water, it carries the things a big river picks up on the way: soil, plant matter, farm runoff and, in late summer, algae. The report shows the treatment system handled that well in 2025. Turbidity, a measure of cloudiness that stands in for how well particles are being filtered out, met the treatment rule 100 percent of the time, with a highest reading of 0.10 NTU. The city also removed between 46 and 59 percent of the river’s total organic carbon, about 55 percent on average, and met every removal requirement.
After treatment, the city adds chloramine, a mix of chlorine and ammonia, to keep the water clean through the pipe network. Chloramine lasts longer than free chlorine and forms fewer disinfection byproducts, but it is harder to remove at home. The city also adds fluoride at a low level for dental health; the report lists an average of 0.67 ppm.
Minneapolis water hardness
Hardness is not in the annual consumer report, but the city’s 2025 yearly record of water data lists total hardness averaging 94 ppm, with a range of 80 to 113 ppm. That works out to roughly 5.5 grains per gallon on average, or about 4.7 to 6.6 gpg across the year. Water in that band is usually called moderately hard. It will leave some spotting on glasses and slow scale in a water heater over time, but it is far softer than the groundwater many Twin Cities suburbs pump. For most Minneapolis homes a full salt-based softener is optional rather than necessary. If spotting bothers you, a softener sized for about 6 gpg is enough, and a whole-house carbon filter will not change hardness at all.
What’s in Minneapolis tap water: detected contaminants
The table below lists every regulated substance the city detected in 2025. “Highest level” is the number the city uses for compliance, which is a running average for disinfection byproducts and chloramine.
| Contaminant | Highest level | Legal limit (MCL) | Health goal (MCLG) | Typical source |
|---|---|---|---|---|
| Nitrate | 0.67 ppm (range 0.65–0.67) | 10 ppm | 10 ppm | Fertilizer runoff, septic systems, natural deposits |
| Total trihalomethanes (TTHM) | 36.8 ppb highest average (range 8.50–66.10) | 80 ppb | None set | Byproduct of disinfection |
| Haloacetic acids (HAA5) | 23.6 ppb highest average (range 2.20–40.90) | 60 ppb | None set | Byproduct of disinfection |
| Chloramine | 3.27 ppm highest average (range 2.70–3.50) | 4.0 ppm (MRDL) | 4.0 ppm (MRDLG) | Added to control microbes |
| Fluoride | 0.67 ppm average (range 0.65–0.69) | 4.0 ppm | 4.0 ppm | Added for dental health; natural deposits |
| Turbidity | 0.10 NTU; 100% of months met the rule | Treatment technique | None | Soil runoff |
The report also lists substances without enforceable limits. Sodium was 18.7 ppm and sulfate 27.3 ppm. Four PFAS were found at trace levels: PFBA up to 12.00 ppt (average 10.12), PFPeA 1.9 ppt, PFHxA 1.28 ppt and PFBS 1.16 ppt, the last three from 2024 sampling. Two algal toxins, anatoxin-a (0.20 ppb) and cylindrospermopsin (0.01 ppb), each turned up once in 14 sampling events between May and November. The city notes these comparison values are not enforceable limits.
Lead and copper in Minneapolis
Lead and copper are measured at household taps, because they usually come from plumbing rather than the river. In the most recent round, sampled on August 15, 2024 at 67 homes, the 90th percentile for lead was 2 ppb, far under the 15 ppb action level, and most results ranged from below 1.0 to 4.0 ppb. One home produced an extreme outlier, which the report prints as 133,000 ppb; follow-up sampling at that home came back below 2 ppb. Copper’s 90th percentile was 0.07 ppm against a 1.3 ppm action level, with one home at 1.48 ppm.
In Minneapolis the property owner owns the whole service line, and the city is replacing lead lines with state and federal money at no cost to owners. The state goal is to finish by 2033. You can check your address on the city’s lead service line map and order a free lead test kit through 311. If your home is older or your line is lead, a filter certified for lead is a sensible bridge until it is replaced.
Violations
None reported. The city states that no contaminants were detected above federal drinking water standards in 2025.
Do you need a filter in Minneapolis?
Match the filter to the finding rather than buying the most expensive system:
- Chloramine taste or smell: this is the most common complaint. Look for catalytic carbon, either as a whole-house system for showers and every tap or an under-sink unit for drinking water. Our whole-house filter guide explains which ones are built for chloramine.
- Lead from an older service line or fixtures: choose a filter certified to NSF/ANSI 53 for lead. Many pitchers and faucet filters qualify; see pitchers and shower filters.
- PFAS peace of mind: the levels found were trace amounts, but reverse osmosis certified to NSF/ANSI 58 is the strongest home option. See reverse osmosis systems.
- Private well outside city service: the city report does not apply to you; start with our well water guide.
FAQ
Is Minneapolis tap water safe to drink?
Minneapolis reports that its water met all federal drinking water standards in 2025, with no contaminants detected above federal limits and no violations. Lead at the tap was low citywide, but homes with lead service lines should test and consider a lead-certified filter. PFAS were detected only at trace levels.
Where does Minneapolis get its water?
All of it comes from the Mississippi River. The city treats the river water, disinfects it with chloramine and adds a small amount of fluoride before it reaches homes.
Does Minneapolis have hard water?
It is moderately hard. The city’s 2025 data averaged 94 ppm of hardness, about 5.5 grains per gallon, so expect light spotting but not the heavy scale common with suburban well water.
Sources: City of Minneapolis 2025 Drinking Water Report (2025 data); City of Minneapolis 2025 record of water data (hardness); Minneapolis water quality reports page. Values change every year and come from the utility’s 2025 report.