St. Louis Tap Water: What’s in It and the Best Filter

Disclosure: we may earn a commission from links on this page, at no cost to you. How we choose filters.

St. Louis Tap Water: What's in It and the Best Filter: illustration of a city skyline with a water drop

Short answer: St. Louis tap water had no contaminant above a federal limit in 2025, according to the City of St. Louis Water Division’s 2025 report, though the utility did log two paperwork violations tied to lead notices. The water is drawn from the Missouri and Mississippi rivers, partly softened at the plant, and disinfected with chloramine, so taste and lead-safety plumbing are the main reasons to filter.

Here is a plain-English look at what the city’s Water Division published about calendar year 2025: where the water starts, how the two plants treat it, the full list of detected contaminants with their limits, lead and copper results, and the violations it disclosed. This page covers customers of the City of St. Louis Water Division. Most of St. Louis County is served by a different utility with its own report. All figures come from the 2025 report and will change next year.

Key takeaways

  • Every detected contaminant stayed below its legal limit; the city reported no MCL exceedances for 2025.
  • Two monitoring and reporting violations involved late lead-related notices, not water contamination, and the utility says both were corrected.
  • Lead was low at the tap: 90th percentile 1.80 ppb across 50 homes in 2025, with no home above the action level.
  • All 29 PFAS tested in 2024 were below the minimum reporting levels.

Where St. Louis tap water comes from and how it’s treated

The city runs two treatment plants. Howard Bend draws from the Missouri River, and Chain of Rocks draws from the Mississippi just below the confluence. Because the two rivers have not fully mixed at that point, the report notes that Chain of Rocks mostly takes in Missouri River water too. Together the plants averaged about 125 million gallons a day in 2025.

Treatment is a multi-step process: chlorine to inactivate parasites, precipitative softening to strip out part of the minerals, settling and flocculation to pull particles out, then filtration. Fluoride is added, and chloramine is used as the lasting disinfectant in the pipes. Chloramine residuals reached 3.44 ppm in the distribution system, under the 4 ppm cap but high enough that many people taste it.

St. Louis water hardness

The 2025 report lists total hardness at 129 ppm as calcium carbonate, with a range of 80 to 206 ppm. That averages about 7.5 grains per gallon and swings from roughly 4.7 to 12 gpg depending on river conditions. The plants already soften the river water, which is why the number is lower than raw Missouri River water would be. At 7 to 8 gpg you will see some scale on fixtures and in kettles. A softener is a reasonable comfort upgrade if you dislike spotting or run a tankless water heater, but it is not a must. A carbon filter alone does not reduce hardness.

What’s in St. Louis tap water: detected contaminants

ContaminantHighest levelLegal limit (MCL)Health goal (MCLG)Typical source
Atrazine0.96 ppb (ND–0.96)3 ppb3 ppbHerbicide runoff from row crops
Arsenic0.42 ppb (0.41–0.42)10 ppb0Erosion of natural deposits
Antimony0.28 ppb (0.27–0.28)6 ppb6 ppbRefinery discharge, solder, flame retardants
Barium0.026 ppm (0.02–0.026)2 ppm2 ppmErosion of natural deposits
Chromium (total)1.11 ppb (1.01–1.11)100 ppb100 ppbNatural deposits, industrial discharge
Selenium1.31 ppb (1.16–1.31)50 ppb50 ppbNatural deposits, industrial discharge
Nitrate (as N)0.58 ppm (0.56–0.58)10 ppm10 ppmFertilizer runoff, natural deposits
Fluoride1.15 ppm (0.21–1.15)4 ppm4 ppmAdded for dental health
TTHM16.9 ppb (4.9–16.9); highest LRAA 11.780 ppbNone setDisinfection byproduct
HAA517.6 ppb (6.4–17.6); highest LRAA 15.460 ppbNone setDisinfection byproduct
Chloramine (distribution)3.44 ppm (1.84–3.44)4 ppm (MRDL)4 ppm (MRDLG)Water treatment additive
Turbidity0.23 NTU; 99.8% of samples under 0.15Treatment techniqueNoneSoil runoff

Disinfection byproducts were notably low for a river system: the highest locational running average for trihalomethanes was 11.7 ppb against an 80 ppb limit. Gross alpha and uranium, last tested in 2022, were not detected. Among unregulated measurements, lithium averaged 27.5 ppb (2024), sodium 45.4 ppm and sulfate 131.0 ppm, and the water ran alkaline, with pH averaging 9.52. Iron and manganese were not detected.

Lead and copper in St. Louis

Between June and September 2025 the city sampled 50 homes. The 90th percentile for lead was 1.80 ppb, with results from non-detect to 6.87 ppb, and no home topped the 15 ppb action level. Copper’s 90th percentile was 0.0238 ppm, far below its 1.3 ppm action level. Those are good numbers, but lead risk in an older city depends on the individual house. The report does not include a count of lead service lines; it points residents to the Water Division’s online lead service line inventory and its phone line at (314) 771-2255. If you live in a pre-1986 home, check the inventory and run a tap test.

Violations

The report lists no health-based violations but two monitoring and reporting violations. First, the city did not certify its lead service line notifications to the state by November 15, 2024; the notices went out by November 25, 2024. Second, notices of 2025 lead and copper tap results and supporting materials were issued later than required (September 30, 2025 and May 21, 2026). The utility says neither posed a public health risk and that it is back in compliance.

Do you need a filter in St. Louis?

  • Chloramine taste: a catalytic carbon system is the fix. For the whole house, see our whole-house filters; for one tap, an under-sink carbon unit works.
  • Older plumbing or a possible lead line: use a filter certified to NSF/ANSI 53 for lead, such as many options in our pitchers and shower filters guide.
  • Atrazine, nitrate or broad reduction: levels were well under limits, but reverse osmosis covers the widest range if you want extra margin. See reverse osmosis systems.
  • On a private well in the region: this report does not cover you; see our well water guide.

FAQ

Is St. Louis tap water safe to drink?

The City of St. Louis Water Division reports that no contaminant exceeded a federal limit in 2025. It did record two monitoring and reporting violations for late lead-related notices, which it says posed no health risk and have been corrected. Lead at the tap was low, and all 29 PFAS tested were below reporting levels; homes with older plumbing should still test for lead.

Where does St. Louis get its water?

From the Missouri River at the Howard Bend plant and the Mississippi River at the Chain of Rocks plant, where the intake still mostly carries Missouri River water.

Does St. Louis have hard water?

It is moderately hard after plant softening: about 129 ppm, or roughly 7.5 grains per gallon on average, ranging from about 4.7 to 12 gpg.

Sources: City of St. Louis Water Division 2025 Water Quality Report (CCR, 2025 data); St. Louis Water Division lead and water page. Figures change each year; these come from the utility’s 2025 report.