Baltimore Tap Water: What’s in It and the Best Filter

Disclosure: we may earn a commission from links on this page, at no cost to you. How we choose filters.

Baltimore Tap Water: What's in It and the Best Filter: illustration of a city skyline with a water drop

Short answer: Baltimore tap water had no contaminant limit violations in 2025, based on the Department of Public Works’ annual report, though the city logged one reporting violation for filing its lead service line inventory late. The figure to watch is disinfection byproducts: the highest running average for total trihalomethanes was 77 ppb, close to the 80 ppb limit.

We pulled every number on this Baltimore tap water page from the Baltimore City Department of Public Works (DPW) 2025 Water Quality Report, which covers January 1 through December 31, 2025. DPW runs the regional system that supplies about 1.8 million customers in Baltimore City and surrounding counties. Results shift from year to year, so treat these as the 2025 snapshot.

Key takeaways

  • Reservoir water: Liberty, Loch Raven and Prettyboy reservoirs supply the system, with the Susquehanna River held in reserve for severe drought.
  • Byproducts run high: TTHM highest locational running average 77 ppb (limit 80) and single samples from 23 to 133 ppb; HAA5 46 ppb (limit 60).
  • PFAS below the coming limits: PFOA peaked at 2.9 ppt and PFOS at 3.3 ppt at Ashburton, under the 4 ppt federal limits that take effect in 2029.
  • Lead looked good in the last round: 90th percentile 2.74 ppb in 2024 with no homes over the action level, but roughly 73,000 service lines were still of unknown material.

Where does Baltimore tap water come from?

Baltimore drinks reservoir water. Three reservoirs north and west of the city hold about 84 billion gallons combined: Liberty (40 billion), Loch Raven (24 billion) and Prettyboy (20 billion). The Susquehanna River is a backup source used only in severe drought. Water is treated at two filtration plants, Ashburton on the west side and Montebello (plants I and II) on the east side, and moves through more than 3,800 miles of water mains.

DPW disinfects with chlorine, not chloramine. The highest chlorine level at the plants was 1.14 ppm (Ashburton) and 1.20 ppm (Montebello), and the distribution system averaged 0.52 ppm across 4,716 samples in 2025, all under the 4 ppm maximum. Because the residual is free chlorine, an ordinary activated carbon filter is enough to remove the pool-like taste some residents notice. Fluoride is added, with plant maximums of 0.90 and 1.09 ppm.

Baltimore water hardness

The 2025 report does not list a hardness value, and neither does DPW’s water quality web page; it mentions mineral reports for pH, alkalinity and dissolved solids instead. We won’t guess at a number. If you see crusty faucets or a scaly kettle, a $10 hardness test strip will give you the reading in grains per gallon. Under about 7 gpg, a softener rarely pays off; above that, compare options in our hard water guide.

Detected contaminants in Baltimore water

This table shows the highest 2025 results the report lists for each plant or for the distribution system. Where two numbers appear, the first is Ashburton and the second is Montebello.

ContaminantHighest levelLegal limit (MCL)Health goal (MCLG)Typical source
Nitrate5.81 ppm / 1.57 ppm10 ppm10 ppmFertilizer runoff
Barium0.0238 ppm / 0.0407 ppm2 ppm2 ppmDrilling waste discharges; natural deposits
Fluoride0.90 ppm / 1.09 ppm4 ppm4 ppmWater additive for dental health
Combined radium 226/2281.6 pCi/L (2019 data)5 pCi/L0Natural deposits
Total trihalomethanes (TTHM)77 ppb highest LRAA (range 23–133)80 ppbn/aChlorination byproduct
Haloacetic acids (HAA5)46 ppb highest LRAA (range 6–53)60 ppbn/aChlorination byproduct
PFOA2.9 ppt / 1.9 ppt4 ppt (from 2029)0Industrial and consumer products
PFOS3.3 ppt / 1.7 ppt4 ppt (from 2029)0Industrial and consumer products
Turbidity0.12 NTU / 0.22 NTU (100% compliant)Treatment techniquen/aSoil runoff
Total coliform1.31% highest monthly positive5% of monthly samples0Naturally present in the environment

Compliance for TTHM and HAA5 is judged on the running average at each sampling site, so a single 133 ppb sample is not a violation. Still, an average of 77 ppb leaves little room under the limit. Long-term exposure to trihalomethanes above the limit is linked to cancer risk, which is why many households filter for them. Activated carbon certified to NSF/ANSI 53 for TTHM reduction is the usual answer. Nitrate at Ashburton reached 5.81 ppm, more than half the limit; that is relevant mainly for infants.

The report also lists PFBS (1.8 and 2.2 ppt) and unregulated PFHxA (2.90 and 2.08 ppt), with PFHxS, PFNA and GenX not detected. The PFAS hazard index was 0.0009 and 0.003 against a limit of 1.0. Read more in what filter removes PFAS.

Lead and copper

Baltimore’s most recent lead and copper compliance round was in 2024; the next is set for 2027. The 90th percentile for lead was 2.74 ppb (range under 2 to 7.09 ppb) and none of the homes tested were above the 15 ppb action level. Copper’s 90th percentile was 112 ppb against a 1,300 ppb action level, also with no homes over.

Those results are reassuring, but the report also notes that about 73,000 service line records of unknown material were left out of the first customer notices in 2024. Until your line is confirmed, check the city’s online service line inventory, flush the tap for 3–5 minutes after water has sat (the report’s advice), and use an NSF/ANSI 53 lead-certified filter for drinking water if your home was built before the late 1980s. Our guide to lead filters lists what to look for.

Violations and deficiencies

No contaminant violations were reported. There was one public notice (reporting) violation: DPW submitted its initial service line inventory to the Maryland Department of the Environment on November 25, 2024, after the October 16, 2024 deadline; the report says public health was not affected. The state has also identified two significant deficiencies, one at a treatment plant and one in the distribution system, both due May 5, 2026, and DPW is rehabilitating filters at Montebello, with Plant 1 scheduled for completion in February 2028.

Do you need a filter in Baltimore?

  • Byproducts and chlorine taste: a carbon block filter certified for TTHM reduction, either a pitcher or faucet unit from our pitcher picks or a whole-house carbon filter if you also want it for showers.
  • Unknown service line or older plumbing: a lead-certified (NSF/ANSI 53) filter at the kitchen sink.
  • Broadest reduction (PFAS, nitrate, byproducts): an under-sink reverse osmosis system.
  • Private well in Baltimore County: DPW’s report doesn’t apply; test your well and start with our well water guide.

FAQ

Is Baltimore tap water safe to drink?

DPW’s 2025 report lists no contaminant limit violations; the only violation was a late service line inventory filing, which the report says did not affect public health. Disinfection byproducts were close to the limit (TTHM 77 ppb vs 80 ppb), PFAS was below the 2029 limits, and homes with unknown service lines may want a lead-certified filter.

Where does Baltimore get its water?

From the Liberty, Loch Raven and Prettyboy reservoirs, treated at the Ashburton and Montebello filtration plants. The Susquehanna River is used only during severe drought.

Does Baltimore use chlorine or chloramine?

Chlorine. The 2025 report lists chlorine (sodium hypochlorite or chlorine) as the disinfectant, with a distribution system average of 0.52 ppm.

Sources: Baltimore City Department of Public Works, 2025 Water Quality Report; DPW Annual Water Quality Report page. Values change each year; the figures above are from the utility’s 2025 report.